Skip to main content

Protect your investment - schedule maintenance today

Wiring repair · Dallas–Fort Worth

Wiring Repair & Electrical Troubleshooting

Sprinkler system not turning on? We diagnose and repair irrigation wiring problems, solenoid failures, and controller issues to get your system running again.

Licensed irrigator · TCEQ LI0023963

Irrigation controller on a garage wall with zone wires connected

Signs of electrical problems

Sprinkler wiring problems: what you see and what usually causes it

These point to wiring, a solenoid, or the controller. The test at the controller and the valve tells us which.

Controller runs but the zone stays off
Failed solenoid, cut wire between controller and valve, or a bad controller output for that zone.
"Shorted Zone" or "Sensor Fault" on the display
A wire grounding out, or damaged rain sensor wiring. "No AC" points to a power problem at the controller.
Whole system dead after a storm
Lightning or surge damage to the controller and solenoids.
Several zones down at once
The common wire or the controller itself, rather than a separate failure at each valve.
Zone works when you bleed the valve, not from the timer
Electrical fault: solenoid, wire, or controller output. The valve itself is opening fine.
Zones quit after landscaping, fence or construction work
A wire cut by a shovel, post hole or trencher. Rodents can sever wire too.
A zone that used to work and quit with no digging nearby
A corroded underground splice. Moisture breaks down old connections over time.
You cannot find the wire path or the valve box
Wire locating and tracing, which also maps where the valves are.
Smart controller on a wall with a wireless rain sensor receiver connected

Wire tracing and controllers

Sprinkler wire tracing and controller repair

Cut wires are common after landscaping, construction, or rodent damage. Our equipment sends a signal through your zone wires and locates the break underground, so we dig at the break and not across your yard.

We service Hunter, Rain Bird, Rachio, Orbit, and Irritrol controllers, from a simple solenoid replacement to a full controller upgrade. Solenoids are carried on the trucks.

Not sure where the problem is? The sprinkler-not-turning-on diagnostic guide walks through each failure point. Commercial site on a decoder system? See two-wire decoder repair.

How we work

Our wiring repair diagnostic process

  1. 1

    Electrical test

    We test each zone at the controller, checking for proper voltage output, solenoid resistance, and wire continuity to identify the failure point.

  2. 2

    Wire trace

    Using professional locating equipment, we trace wire paths and pinpoint breaks, shorts, or ground faults in your system.

  3. 3

    Targeted repair

    We excavate only at the problem location, splice in new wire with waterproof connectors, or replace the failed component.

  4. 4

    Full system test

    Each zone is cycled through the controller to verify repairs and confirm proper operation before we leave.

Sprinkler wiring repair FAQs

Why won't my sprinkler zone turn on?

The most common causes are: failed solenoid (the electromagnetic coil on the valve), cut or damaged wire between controller and valve, bad controller output for that zone, or corroded wire connections underground. Our diagnostic identifies exactly which component has failed.

How do you find a cut wire underground?

We use professional wire locating equipment that sends a signal down the wire and detects where it stops. This pinpoints the break location within inches, so we only dig where needed instead of excavating your entire yard.

My sprinkler timer shows an error - what does it mean?

Common error codes indicate electrical issues: "Shorted Zone" means a wire is grounding out, "No AC" indicates power problems, "Sensor Fault" points to rain sensor wiring. We can interpret the codes and fix the underlying issue.

Can a power surge damage my sprinkler system?

Lightning strikes and power surges can fry irrigation controllers and solenoids. If your system stopped working after a storm, surge damage is likely. We assess which components are affected and repair or replace as needed.

How much does irrigation wiring repair cost?

Costs vary based on the problem. A simple solenoid replacement costs far less than tracing and splicing a wire break across your yard. When you accept our repair estimate, you'll receive a discount on your total service. We provide clear pricing before any work begins.

Do you repair two-wire decoder systems?

Yes. Commercial properties and large HOAs often run two-wire decoder systems, which fail differently than conventional wiring. See our two-wire decoder repair page for how we diagnose line faults and decoder failures.

Should I replace my old controller?

If your controller has multiple failed outputs or recurring problems, replacement often makes more sense than repeated repairs. Modern controllers offer WiFi control, weather-based scheduling, and better reliability. We can help you decide based on your system's condition.

Schedule sprinkler wiring repair

Contact Better Earth Solutions for diagnosis and repair of your sprinkler wiring issues. Receive a discount when you accept repairs.

Last updated: